Nov 13th, 2005, 17:17 | 只看该作者 #201 | |
▂ ▂ ▃ ▄ ▅ ▆
注册日期: Jul 2004
住址: ROD
帖子: 3,292
积分:5
精华:5
|
引用:
all u need is here. http://www.al7bar.tk/forums/showthre...368#post254368 |
|
晕呢
|
||
|
Nov 13th, 2005, 19:14 | 只看该作者 #202 | |
Junior Member
注册日期: Nov 2005
帖子: 16
声望: 10
|
ok, I struggled a whole afternoon to cut the cable to below 6'' but,
引用:
problem still same. now i can't make the cable shorter. i used bluewhale's jkeys.def, and go through his instruction step by step. the processor ID and device can be correctly detected, but there is always IRD reading error when you click the detect button. I checked the old post in chinasmile and someone had the same experience as mine, as he suggested, it was still the cable's problem. but I've double checked the connection and grounding, everything looks ok. maybe i have to make another jtag cable with buffer. |
|
|
Nov 13th, 2005, 20:31 | 只看该作者 #203 | |
Senior Member
注册日期: Jul 2004
帖子: 547
积分:6
精华:2
声望: 186919
|
引用:
Thank you very much. Just like what you mentioned here, after I tried to changed the key many times by different ways, my receiver PANSAT2500A has worked very well since last week. Hi HHH, How's going? Sorry I have not been in the fotum for few days, because the forume was being updated. Now, everything is OK, also including my job. I am going to start my new job from Nov. 21st. Keep in touch. |
|
|
Nov 13th, 2005, 20:33 | 只看该作者 #204 | |
Member
注册日期: Sep 2005
帖子: 36
声望: 10
|
引用:
|
|
|
Nov 13th, 2005, 21:14 | 只看该作者 #206 | |
Junior Member
注册日期: Nov 2005
帖子: 10
声望: 10
|
Thanks for the understanding
引用:
This might be the file I used yesterday to refresh the bin and key(as the "read me" document is the same). I just didn't do the second step (Input channel list) as I could not find the "Write User data" button on the menu. There is only one named "Read User data". So I didn't do it. So should I try the whole process again? What should I do if there is still no "Write User data" to choose from? Thanks!! |
|
|
Nov 13th, 2005, 21:24 | 只看该作者 #207 | |
Junior Member
注册日期: Nov 2005
帖子: 10
声望: 10
|
引用:
1. signal quality is about 60-68 (keep changing), and the color is in grey, i heard it should be in yellow. 2. I was told to check the numbers of each TP and manually input them. 3. still could not figure out where to change "position", no such choice on the menu. Thanks! |
|
|
Nov 14th, 2005, 09:51 | 只看该作者 #210 | |
▂ ▂ ▃ ▄ ▅ ▆
注册日期: Jul 2004
住址: ROD
帖子: 3,292
积分:5
精华:5
声望: 78577954
|
引用:
|
|
|
Nov 14th, 2005, 20:40 | 只看该作者 #214 | |
▂ ▂ ▃ ▄ ▅ ▆
注册日期: Jul 2004
住址: ROD
帖子: 3,292
积分:5
精华:5
声望: 78577954
|
引用:
|
|
|
Nov 14th, 2005, 20:41 | 只看该作者 #215 | |
Senior Member
注册日期: Jul 2004
帖子: 6,096
积分:5
精华:3
声望: 8049986
|
引用:
something called sw21 or sw34. it's a switch. Or DiSCEqC, 4 in 1 out. |
|
|
Nov 14th, 2005, 20:57 | 只看该作者 #216 |
Junior Member
注册日期: Nov 2005
帖子: 16
声望: 10
|
Hi, FireROR or BlueWhale, I have a new problem in Jtagging
I made a new Jtag cable, now Jkeys can accept the IRD I entered and can recognize the flash type 39vf800a. I try read mem and save image, it works. but when I try to erase or program the flash, it give the error: Flash timeout(DQ5 set). because my machine is a pansat 2500a clone, i have to solder the jtag cable directly to the FPGA. but i check the soldering very carefully, there is no sign of bridge or open. could you please give me some idea for that? i am so frustrated with this machine |
|
Nov 14th, 2005, 21:30 | 只看该作者 #219 | |
Senior Member
注册日期: Nov 2004
帖子: 1,217
积分:2
精华:2
声望: 69630
|
我想我知道你的问题在那里了。
引用:
再不行,试试把22Khz打开到ON。 总之Signal Strength必须是黄色条,数值稳定在60以上才能看。 |
|
|
Nov 14th, 2005, 21:34 | 只看该作者 #220 | |
Senior Member
注册日期: Nov 2004
帖子: 1,217
积分:2
精华:2
声望: 69630
|
当然要调到这个频率。
引用:
另:Universal LO: 9750/10600,通过22Khz信号来选择是用9750还是10600。 Linear LO: 10750,22Khz信号没用,因其LO是固定的。 不要混淆。 |
|
|