Feb 12th, 2008, 19:25 | #1 |
Senior Member
|
准备收BEV,别的先不管。 研究了不少时间,似乎以下配置还说得过去。 请对以下配置提提意见: 天线:Elliptical Dish w/ 4 x DSS dual LNB's,(Includes 4 DSS dual LNB's and 1 extension bracket。能收82, 91, 101, 110, and/or 119),88$。 接收机:CaptiveWorks CW-700s,110$。 开关及接线:开关目前还不太清楚。 工具:39.5$。 |
|
Feb 19th, 2008, 01:58 | #2 |
Senior Member
|
Bell双星不需要椭圆天线吗?
|
|
Mar 3rd, 2008, 19:56 | #3 |
Senior Member
|
从最基本地开始请教: 首先准备买这些设备,大家看看是不是合适。 1)天线:24‘ Elliptical Dish w/ 4 x DSS dual LNB's, 88 2)开关:Chieta Heavy-Duty 4x1 DiSEqC Switch, 9.9 3)线放:Inline Amplifier, 5.5 4)接收机: 5)电缆及F头若干 线路的拓扑结构的大体构想是: 天线1)自带4个LNB,信号经开关2)合并后经室外的ROGERS的接线盒引入室内。信号经室内已经有的(原来给ROGERS预留的线)去3个房间。 比较讨厌的是在这个接线盒里又SPLIT成3股去室内3个房间。这时有几个问题请教。 假设这个接线盒的SPLITTER有一定的损耗。可以分别接入3个线放3)补偿。或者在SPLITTER前接入1个线放3)也可。 -〉如果这个SLPLITTER频率上不了2G。是不是可以把开关2)倒过来使用呢? -〉这里预留的线是否能上到2G? |
|
Mar 3rd, 2008, 22:07 | #4 | |
Senior Member
|
引用:
1)是不是DiSEqC Switch不能象无源的器件那样反过来用? 2)预留线长度还真不好说。难道不能用线放补偿吗? 查了一下4进4出的SW44 要接近90块。8进3出的还没找到。 其实也不是要4颗星。目前目标是有bev的2颗足够。将来有机会再换成STAB的USALS的HH-120电机。 此帖于 Mar 3rd, 2008 22:27 被 dalplex 编辑。 |
|
|
Mar 10th, 2008, 19:51 | #5 |
Senior Member
|
在别的地方问没人理。在这再麻烦一下。 外墙砖尺寸是3x4.5x12英寸。 内有5个拉长的圆型像体育场跑道形状的孔。 这种砖算hollow砖吗? 应该用Tapcon还是Hollow Wall Toggler?还是用膨胀螺栓? 另:随Tapcon内带的钻头看起来也不是masorny钻头。对这种砖大家都用什么钻头呢? |
|
Mar 10th, 2008, 20:45 | #6 | |
Senior Member
|
引用:
从图中能看出来它的螺纹在上部消失了。因此如果穿过砖的空心部分根本就不起作用。 Toggler是一种专用的挺有意思的小玩意。 比如Hollow或cinder block能猜出来是空心或煤渣砖。但是真正什么是空心或者煤渣砖就难说了。而且种类繁多。 我提到的砖是Cored Brick。这张图中看得比较清楚。中间那个颜色比较浅的就是。 该用什么钻头和螺丝就不好说料。 因为不知道那个底盘所用的孔(应该有6个)的距离。如果正好打在孔里。那个地方到表面的厚度才1厘米左右,就是用Tapcon强度也够呛呀。 此帖于 Mar 10th, 2008 21:17 被 dalplex 编辑。 |
|
|
Apr 9th, 2008, 19:40 | #7 |
Senior Member
|
CaptiveWorks700s并不works. 已经升级4月4日的1.57的Bin. 几乎不用调天线,信号就很强。 能看到台标。但是全是Scrambled Channel。 是不是都这样呀? 此帖于 Apr 9th, 2008 20:15 被 dalplex 编辑。 |
|
Apr 9th, 2008, 20:14 | #8 |
Senior Member
|
|
|
Apr 9th, 2008, 21:13 | #9 |
Senior Member
|
请问在那能看/找到最新的bin呢? 照目前这种局面是不是该多买几个不同牌子的接收机呢? 最后可能还是老老实实租交钱的吧。 |
|
Apr 10th, 2008, 05:19 | #10 |
Senior Member
|
|
|
Apr 10th, 2008, 18:06 | #11 | |
Senior Member
|
引用:
LNB应该是普通的就可以。 此帖于 Apr 10th, 2008 19:45 被 dalplex 编辑。 |
|
|
Apr 12th, 2008, 09:55 | #12 |
Senior Member
|
CaptiveWork 700长宽比似乎调不了? 收下来的信号是704*480。约4.4/3。 电视是1920*1080。是16/9。 怎么看都不对。 调电视和接收机的长宽比都不能调到满屏(变形的不算)。 我记得贝尔的接收机能调长宽比。 请问CW的长宽比调节是否有效? |
|
Apr 15th, 2008, 02:21 | #13 |
Senior Member
|
实在忍无可忍了。 准备上VS 9000HD。 |
|
Apr 15th, 2008, 09:24 | #14 |
Senior Member
|
现在有一个实际的问题请教: 3室一厅已经预埋3根线。也就是有一个房间没有线。埋暗线太难,拖明线有碍眼。 目前有单碟双LNB双输出共4根线进户经4X1 DiSEqC转一根线。 用4X3开关可以实现3个接收机同时看。用4X4可以4个接收机但那个没有线的房间还是没戏。 计划把一个LNB的信号经一根电缆越过DiSEqC直接接已经预埋的一根线然后SPLITTER去两个房间(其中一个没有预埋线)。 问题: 假设那个没有预埋线的房间只要求与另一个房间看同一个星的信号(可能TP不同)。 有否可能用一个SPLITER把经同一根线;来自同一个星的信号分开供连个接收机同时使用? 如不能同时使用是否可分时使用? |
|
Apr 15th, 2008, 14:57 | #15 |
Senior Member
|
|
|
Apr 16th, 2008, 12:24 | #16 |
Senior Member
|
|
|
Apr 17th, 2008, 02:03 | #17 |
Senior Member
|
请问CW700S的调长宽比的功能到底有效否?
|
|
Apr 26th, 2008, 23:22 | #18 |
Senior Member
|
看来调星还是不到家。 用的是那种有两个LNB的18寸的天线。因为两个频道重复的很多。最后我都弄不清到底对的是哪一颗了。而且角度非常窄,几乎差一点都不行。 调来调去只能假设收到高经度的。那个低经度的有高清的就是有强度无质量。 奇怪的是接在接收机上后。有些显示是低度的频道却也能看到。这时为何呢? |
|
Apr 26th, 2008, 23:23 | #19 |
Senior Member
|
|
|
Apr 28th, 2008, 21:09 | #20 |
Senior Member
|
|
|